Running eHS on an OP5600 with OP5142 card: target missing in Schematic Editor and OP5142 library empty in MATLAB

Hello everyone,

I am trying to run the eHS solver on an OP5600 chassis equipped with an OP5142 card, and I am stuck on two points.

*Configuration

  • Target: OP5600 chassis with an OP5142_1 card (EX bus)
  • Current bitstream: OP5142_1-EX-0000-2_1-96IO-04-01.bin (I/O only: 16 AO, 16 AI, 16+16 DI, 16+16 DO)
  • RT-LAB 2022.1, MATLAB R2021b
  • Schematic Editor v2.10.0.2568
  • OPAL-RT Flash Update V2.4 correctly detects the card: board index 0, OP5142_1, PCIe gen 1 (x1)

*Issues

  1. In the Schematic Editor, the Simulator Setup only offers Local, OP5707, and OP4510. The OP5600 / OP5142 does not appear, so I cannot select my target.
  2. In MATLAB/Simulink, the RT-LAB I/O > Opal-RT > OP5142 library is empty.

*Questions

  1. Is eHS supported on the OP5142 with RT-LAB 2022.1? If so, which version of eHS and which version of the Schematic Editor should I use?
  2. Is there a dedicated eHS bitstream for the OP5142? How can I obtain and flash it? Is a specific license required?
  3. Why would the OP5142 block library be empty with RT-LAB 2022.1 and MATLAB R2021b? Is there a MATLAB registration step or an I/O block installation step that I might have missed?
  4. If eHS on the OP5142 is not supported in this version, what alternative do you recommend (older toolchain, or simulation on CPU with the OP5142 used only for I/O)?

My goal is to simulate a power electronics system (DC-DC converters, DC bus, AC/DC converter, LC filter) connected to a grid model.

I can provide screenshots and the system description document via private message if necessary.

Thank you in advance for your help.

Hi, I had a similar issue before where the simulator was not appearing properly in RT-LAB. In my case, it was worth first checking that the target had been added/configured correctly in RT-LAB and that the host could actually see it.

For the eHS side, I think the I/O-only bitstream you listed may be relevant as eHS needs a compatible FPGA bitstream/firmware as well as the software and licence, rather than RT-LAB alone. I would be careful not to flash anything until Support confirms the exact OP5142/RT-LAB 2022.1/eHS combination.

Have you been able to see the OP5600 target elsewhere in RT-LAB, or is it only missing from Schematic Editor? Also, do you know whether the OP5142 was supplied with any eHS-specific firmware or licence information? That might help narrow down whether this is a target-configuration issue or an eHS compatibility issue.

Thank you for your feedback and for providing these details.

After checking on my end, it appears that the issue is related to the compatibility of the OP5142 card with the version of eHS already installed and licensed on our system.

The eHS license is active, and RT-LAB 2022.1 as well as the OP5600 target are correctly configured and detected. However, I cannot find the OP5142 in the Hardware Setup of Schematic Editor, nor do I have the corresponding firmware to configure it with the installed version of eHS.

Based on the checks performed, it is therefore possible that the OP5142 is not compatible with the version of eHS for which we currently hold a license, or that the required FPGA firmware does not correspond to this version.

Hello

I think resolution of this might need you to share license details, so raising a support ticket would be a good option here. Can you please raise your concern on our support portal?